View TC57_71035.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TC57
Line Regulator Controller
Features
* Low Dropout Voltage: 100mV @ 650mA with FZT749 PNP Transistor * 2.7V to 8V Supply Range * Low Operating Current: 50A Operating, 0.2A Shutdown * Low True Chip Enable * Output Accuracy < 2% * Small Package: 5-Pin SOT-23A
General Description
The TC57 is a low dropout regulator controller that operates with an external PNP pass transistor, allowing the user to tailor the LDO characteristics to suit the application at hand. This results in lower dropout operation (and often lower cost) compared with traditional linear regulators with on-board pass transistors. The maximum output current of a TC57based regulator circuit is limited only by the characteristics of the external pass transistor. For example, a maximum output current of 650mA (with a dropout voltage of 100mV) results when an FZT749 pass transistor is used, while a Darlington configuration can deliver up to 4A. Flexibility, and superior performance make this family of regulator controllers the ideal choice in applications where low dropout voltage and low installed cost are key.
Applications
* * * * * Battery Operated Systems Portable Instruments High-Efficiency Linear Regulator Post-Regulator for SMPS Power Supply or Battery Back-Up Supply for Memory
Device Selection Table
Output Part Number Voltage TC572502ECT TC573002ECT TC573302ECT 2.5V 3.0V 3.3V Package Temperature Range
Functional Block Diagram
VIN +3.3V FZT749 Q1 VOUT +3V
5-Pin SOT-23A -40C to +85C 5-Pin SOT-23A -40C to +85C 5-Pin SOT-23A -40C to +85C
RBE 47K CIN 10F (Tantalum)
RB 1K 4 EXT VIN
2
VOUT
3
CL 10F (Tantalum)
RL
OFF
TC573002ECT
ON 5 SHDN GND 1
Other output voltages and package options are available. Please contact Microchip Technology Inc. for details.
Package Type
3.3V Line Input, 3.0V, 500mA Output LDO
5-Pin SOT-23A
SHDN 5 EXT 4
TC57
1 GND 2 VIN 3 VOUT
NOTE: 5-Pin SOT-23A is equivalent to the EIAJ SC-74A.
2002 Microchip Technology Inc.
DS21437B-page 1
(c)
TC57
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings*
Input Voltage ........................................................+12V Output Current .................................................... 50mA Output Voltage............................. -0.3V to (VIN + 0.3V) Power Dissipation.............................................150mW Operating Temperature Range............. -40C to +85C Storage Temperature Range .............. -40C to +150C
*Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.
TC55 ELECTRICAL SPECIFICATIONS
TC57EP3002 Electrical Characteristics: SHDN = GND, VIN = VOUT + 1V, VOUT = 3V to 5V, IOUT = 0, TA = 25C, Test Circuit of Figure 3-1, unless otherwise noted. (Note 2) Symbol VIN VEXT VOUT V OUT VIN - VOUT IDD ISHDN Parameter Input Voltage Voltage on EXT Output Output Voltage Load Regulation Dropout Voltage Supply Current Shutdown Supply Current Min -- -- -60 -- -- -- -- -- -- -- 1.5 -- -- -0.2 Typ -- -- -- 100 50 -- 0.1 100 -- -- -- -- -- -0.05 Max 8 8 60 -- 80 0.6 0.3 -- 0.5 25 -- 0.25 0.1 0 Units V V V mV mV A A %/V ppm/C A mA V V A A VSHDN = VIN = 5V VSHDN = GND Note 4 IOUT = 50mA (Note 1) 1mA IOUT 100mA (Note 3) IOUT = 100mA (Note 2) VSHDN = VIN = 5V VSHDN = GND IOUT = 50mA, 4V VIN 8V (Note 3) IOUT = 10mA, -40C < TJ < +85C (Note 3) Test Conditions
0.98 X VR VR 0.5% 1.02 X VR
V OUT/VIN Line Regulation VOUT/T ILEXT IEXT VIH VIL IIH IIL
Note 1: 2: 3: 4:
VOUT Temperature Coefficient EXT Pin Leakage Current EXT Sink Current SHDN Input High Logic Threshold SHDN Input Low Logic Threshold SHDN Input Current @ VIH SHDN Input Current @ VIL
VR is the regulator output voltage setting. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a 1V differential. Varies with type of pass transistor used. Numbers shown are for the test circuit of Figure 3-1. The product of IEXT X VEXT must be less than the maximum allowable power dissipation.
(c)
DS21437B-page 2
2002 Microchip Technology Inc.
TC57
2.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
Pin No. (5-Pin SOT-23A) 1 2 3 4 5
PIN FUNCTION TABLE
Symbol GND VIN VOUT EXT SHDN Ground terminal. Supply voltage input. Positive input voltage of 2.7V to 8.0V. Regulator voltage sense input. Connects to the collector of the external PNP pass transistor. Base Drive for the external PNP pass transistor. Shutdown Input. The device is enabled when SHDN VIL. The device enters a low power shutdown state when SHDN VIH . During shutdown, the output is disabled, and supply current falls to less than 1A. Description
2002 Microchip Technology Inc.
DS21437B-page 3
(c)
TC57
3.0 DETAILED DESCRIPTION
3.2 Base-Current Limiting Resistor
The TC57 series of precision low dropout regulator controllers use an external PNP transistor to accommodate a wide range of output currents. A series resistor (RB) limits the maximum base current drawn from the PNP transistor. Limiting the base drive both determines the regulator's output current capability, as well as limits ground current when the device is operated in dropout. The PNP transistor's VCE(SAT) is the only factor limiting dropout voltage. Base current limiting resistor R B can be estimated using:
EQUATION 3-3:
RB = Where: hFE is the current gain of the pass transistor VIN Is the input voltage (in volts) hFE (VIN - VBE) IOUT
FIGURE 3-1:
VIN
TEST CIRCUIT
FZT749 Q1 VOUT
VBE is the base-emitter voltage at the desired output current (in volts) IOUT is the output current (in Amps) For example, assume a desired continuous output current of 1.0A, an input voltage of 5V, and an FZT749 pass transistor. The FZT749 has a typical hFE of 170, and a VBE of 0.8V; both specified at a collector current of 1.0A. Substituting these values into the equation above results in an RB value of 704 (closest standard value = 680).
RBE 33K CIN 10F (Tantalum)
RB 680 4 VOUT 3
EXT 2V IN OFF ON 5
CL 10F (Tantalum)
RL
TC573002ECT
SHDN GND 1
3.3 3.1 Transistor Selection
The PNP pass transistor must have satisfactory power dissipation, current gain, and collector current specifications to suit the application at hand. The maximum output current the circuit can deliver is influenced by hFE. The highest guaranteed output current is given by:
Pull-Up Resistor and Output Capacitor
EQUATION 3-1:
ILOAD(MAX) = 25 mA x hFE(MIN) The transistor's actual power dissipation (PD) is equal to the maximum load current times the maximum input/ output voltage differential, or:
A pull-up resistor (RBE, installed between the base and emitter of the pass transistor) facilitates rapid turn-off of the pass transistor in the event of a sudden decrease in load (Figure 3-2). Recommended values for this resistor are between 20K and 47K. A Tantalum output capacitor of at least 10F must be used to guarantee stability. Higher values decrease output noise and eliminate power-on overshoot, but extend power-up times. Table 3-1 lists several capacitor choices.
FIGURE 3-2:
3.3V, 1A REGULATOR USING 5V SUPPLY INPUT
FZT749 Q1 VOUT = 3.3V
EQUATION 3-2:
PD ILOAD(MAX) x (VIN(MAX) - VOUT(MIN)) The ideal transistor has a minimum hFE of 100, and a VCE(SAT) of less than 0.6V at full output current. For example, the Zetex FZT749 has an hFE of 170 at a collector current of 1A, and a guaranteed VCE(SAT) of 0.3V at a base current of 100mA. It is packaged in a SOT-223 and is recommended for use with the TC57. Other transistors are also suitable, depending on the required input and output voltages and output current (Table 3-1).
VIN = 5V
CIN 10F (Tantalum)
RBE 33K
RB 680 4 EXT
COUT 10F (Tantalum)
2V IN 1 5 GND SHDN
VOUT 3
TC57
OFF ON
(c)
DS21437B-page 4
2002 Microchip Technology Inc.
TC57
3.4 Input Capacitor 3.5 Shutdown Mode
The addition of an input capacitor further reduces output noise, and negates the effects of power supply input impedance. A 10F (min) Tantalum capacitor is recommended. The TC57 enters a low power shutdown mode when the shutdown input (SHDN) is high. During shutdown, the regulator is disabled, the output capacitor is discharged through the load, and supply current to the TC57 decreases to less than 1A. Normal operation resumes when SHDN is brought low. If the shutdown mode is not used, SHDN should be tied to VIN.
TABLE 3-1:
COMPONENT SUPPLIERS
Mounting Method Manufacturer Website
Device CAPACITORS 267 Series F95 Tantalum Series 595 Tantalum Series OS-CON Series LXF Series TRANSISTORS ZTX749 2N4403 2N2907A FZT749
Surface Mount Surface Mount Surface Mount Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Surface Mount
Matsuo Nichicon Sprague Sanyo United Chemi-Con Zetex ON SEMI ON SEMI Zetex
http://www.matsuoelectronics.com http://www.nichicon-us.com http://www.vishay.com/brands/sprague http://www.sanyovideo.com http://chemi-con.com http://www.zetex.com http://www.onsemi.com/home http://www.onsemi.com/home http://www.zetex.com
2002 Microchip Technology Inc.
DS21437B-page 5
(c)
TC57
4.0
Note:
TYPICAL CHARACTERISTICS
The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
1. OUTPUT VOLTAGE vs. OUTPUT CURRENT
TC575002 (5V)
TA = 25C VIN = 6V, CL = 10F (Tantalum) 5.1 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) 4.1 OUTPUT VOLTAGE VOUT (V)
TC574002 (4V)
TA = 25C VIN = 5V, CL = 10F (Tantalum) 3.4
TC573302 (3.3V)
TA = 25C VIN = 4.3V, CL = 10F (Tantalum)
5.0
4.0
3.3
4.9
3.9
3.2
4.8
3.8
3.1
4.7 0 100 200 300 400 500 OUTPUT CURRENT IOUT (mA)
3.7 0 100 200 300 400 500 OUTPUT CURRENT IOUT (mA)
3.0 0 100 200 300 400 500 OUTPUT CURRENT IOUT (mA)
2. OUTPUT VOLTAGE vs. INPUT VOLTAGE
TC575002 (5V)
CL = 10F (Tantalum), TA = 25C 5.2 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) IOUT = 1mA 500mA 5.10 IOUT = 1mA 500mA 100mA 4.95 OUTPUT VOLTAGE VOUT (V)
TC575002 (5V)
CL = 10F (Tantalum), TA = 25C 4.2
TC574002 (4V)
CL = 10F (Tantalum), TA = 25C
5.0 4.8
5.05
4.0 3.8
IOUT = 1mA A 500mA
5.00
4.6
3.6 100mA 3.4 3.2 3.5
100mA
4.4 4.2 4.5
4.90 4.85
5.0 INPUT VOLTAGE VIN (V)
5.5
5
6
7
8
4.0 INPUT VOLTAGE VIN (V)
4.5
INPUT VOLTAGE VIN (V)
TC574002 (4V)
CL = 10F (Tantalum), TA = 25C 4.10 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) 3.5
TC573302 (3.3V)
CL = 10F (Tantalum), TA = 25C 3.40 OUTPUT VOLTAGE VOUT (V)
TC573302 (3.3V)
CL = 10F (Tantalum), TA = 25C
4.05 IOUT = 1mA
3.3 IOUT = 1mA 3.1 500mA
3.35 IOUT = 1mA, 100mA 3.30 500mA 3.25
4.00
3.95
100mA, 500mA
2.9 100mA 2.7 2.5 2.8
3.90 3.85 4 5 6 7 INPUT VOLTAGE VIN (V)
3.20 3.15
3.3 INPUT VOLTAGE VIN (V)
3.8
3
4 5 INPUT VOLTAGE VIN (V)
6
(c)
DS21437B-page 6
2002 Microchip Technology Inc.
TC57
4.0 TYPICAL CHARACTERISTICS (CONTINUED)
3. DROPOUT VOLTAGE vs. OUTPUT CURRENT
TC575002 (5V)
CL = 10F (Tantalum) 1.0 DROPOUT VOLTAGE VIN -VOUT DROPOUT VOLTAGE VIN -VOUT 1.0 DROPOUT VOLTAGE VIN -VOUT 0.8 0.6
TC574002 (4V)
CL = 10F (Tantalum) 1.0 0.8
TC573302 (3.3V)
CL = 10F (Tantalum)
0.8
0.6 80C
0.6
0.4 0.2 0.0 0 200
TOPR = 25C
0.4 TOPR = 25C R 0.2 0.0
80C
0.4 0.2
80C TOPR = 25C 25
-30C 3 400 600 800 1000
-30C 0 0 200 400 600 800 1000
-30C 0.0 0 200 400 600 800 1000 OUTPUT CURRENT IOUT (mA)
OUTPUT CURRENT IOUT (mA)
OUTPUT CURRENT IOUT (mA)
4. SUPPLY CURRENT vs. INPUT VOLTAGE
TC575002 (5V)
50
SUPPLY CURRENT IDD (A) SUPPLY CURRENT IDD (A)
TC574002 (4V)
50
SUPPLY CURRENT IDD (A)
TC573302 (3.3V)
50
40 TOPR = 25C, 80C 30 -30C 20
40
40 30 TOPR = 25C, 80C
30
TOPR = 25C, 80C -30C
20
20
-30C
10 0 5 6 7 8 INPUT VOLTAGE VIN (V)
10 0 4 5 6 7 INPUT VOLTAGE VIN (V)
10 0 3 4 6 5 INPUT VOLTAGE VIN (V)
5. OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE
TC575002 (5V)
VIN = 6.0V IOUT = 100mA, CL = 10F (Tantalum) 5.10 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) 4.10 OUTPUT VOLTAGE VOUT (V)
TC574002 (4V)
VIN = 5.0V IOUT = 100mA, CL = 10F (Tantalum) 3.40
TC573302 (3.3V)
VIN = 4.3V IOUT = 100mA, CL = 10F (Tantalum)
5.05
4.05
3.35
5.00
4.00
3.30
4.95
3.95
3.25
4.90 -40
-20
0
20
40
60
80
3.90 -40
3.20 -20 20 40 60 0 AMBIENT TEMP. TA (C) 80 -40 -20 0 20 40 60 80 AMBIENT TEMP. TA (C)
AMBIENT TEMP. TA (C)
2002 Microchip Technology Inc.
DS21437B-page 7
(c)
TC57
4.0 TYPICAL CHARACTERISTICS (CONTINUED)
6. SUPPLY CURRENT vs. AMBIENT TEMPERATURE
TC575002 (5V)
VIN = 6V 50
SUPPLY CURRENT IDD (A) SUPPLY CURRENT IDD (A)
TC574002 (4V)
VIN = 5V 50
SUPPLY CURRENT IDD (A)
TC573302 (3.3V)
50 40 VIN = 4.3V
40
40 30
30
30
20 10 0 -40
20
20 10
10 0
0 -40 -20 0 20 40 60 80 -40 AMBIENT TEMP. TA (C) 0 20 40 60 -20 AMBIENT TEMP. TA (C) 80
-20
0
20
40
60
80
AMBIENT TEMP. TA (C)
7. INPUT TRANSIENT RESPONSE
TC575002 (5V)
IOUT = 10mA, CL = 10F (Tantalum) 8 INPUT VOLTAGE VIN (V) Input Voltage 5.3 5.4 OUTPUT VOLTAGE VOUT (V) INPUT VOLTAGE VIN (V) 8 Input Voltage 5.3
TC575002 (5V)
IOUT = 100mA, CL = 10F (Tantalum) 5.4 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V)
7
7
6
5.2
6
5.2
5
Output Voltage
5.1
5
Output Voltage
5.1
4 3 Time (0.4 msec/div)
5.0 4.9
4 3 Time (0.4 msec/div)
5.0 4.9
TC574002 (4V)
7 INPUT VOLTAGE VIN (V) IOUT = 10mA, CL = 10F (Tantalum) 4.4 INPUT VOLTAGE VIN (V) Input Voltage 6 4.3 OUTPUT VOLTAGE VOUT (V) 7
TC574002 (4V)
IOUT = 100mA, CL = 10F (Tantalum) 4.4 Input Voltage 6 4.3
5
4.2
5
4.2
4
Output Voltage
4.1
4
Output Voltage
4.1
3 2 Time (0.4 msec/div)
4.0 3.9
3 2 Time (0.4 msec/div)
4.0 3.9
(c)
DS21437B-page 8
2002 Microchip Technology Inc.
TC57
4.0 TYPICAL CHARACTERISTICS (CONTINUED)
7. INPUT TRANSIENT RESPONSE (CONT.)
TC573302 (3.3V)
IOUT = 10mA, CL = 10F (Tantalum) 6 Input Voltage INPUT VOLTAGE VIN (V) 5 3.6 3.7 OUTPUT VOLTAGE VOUT (V) INPUT VOLTAGE VIN (V) 6 Input Voltage 5 3.6
TC573302 (3.3V)
IOUT = 100mA, CL = 10F (Tantalum) 3.7 OUTPUT VOLTAGE VOUT (V)
OUTPUT CURRENT IOUT (mA)
4
3.5
4
3.5
3
Output Voltage
3.4
3
Output Voltage
3.4
2 1 Time (0.4 msec/div)
3.3 3.2
2 1 Time (0.4 msec/div)
3.3 3.2
8. LOAD TRANSIENT RESPONSE
TC575002 (5V)
VIN = 6V, CL = 10F (Tantalum) 5.10
OUTPUT VOLTAGE VOUT (V)
TC574002 (4V)
VIN = 5V, CL = 10F (Tantalum) 1000
OUTPUT CURRENT IOUT (mA) OUTPUT VOLTAGE VOUT (V)
4.10 4.05
1000 800
5.05
Output Voltage
800
5.00
600
4.00
Output Voltage
600
4.95 300mA 4.90 4.85 1mA
Output Current
400
3.95 300mA 3.90 3.85 1mA
400 Output Current 200 0 Time (10 msec/div)
200 0 Time (10 msec/div)
TC573302 (3.3V)
VIN = 4.3V, CL = 10F (Tantalum) 3.40
OUTPUT VOLTAGE VOUT (V)
1000 Output Voltage
OUTPUT CURRENT IOUT (mA)
3.35
800
3.30
600
3.25 300mA 3.20 3.15 1mA
Output Current
400
200 0 Time (10 msec/div)
2002 Microchip Technology Inc.
DS21437B-page 9
(c)
TC57
5.0
5.1
PACKAGING INFORMATION
Package Marking Information
2
represents first decimal of output voltage Symbol Voltage .0 .1 .2 .3 .4 Symbol 5 6 7 8 9 Voltage .5 .6 .7 .8 .9
3
0 1 2 3 4
3
1
represents integer part of output voltage Symbol 2 3 4 5 6 Voltage 2. 3. 4. 5. 6.
represents production lot ID code
5.2
Taping Form
Component Taping Orientation for 5-Pin SOT-23A (EIAJ SC-74A) Devices
User Direction of Feed
Device Marking
W
PIN 1
P Standard Reel Component Orientation TR Suffix Device (Mark Right Side Up)
Carrier Tape, Number of Components Per Reel and Reel Size
Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size
5-Pin SOT-23A
8 mm
4 mm
3000
7 in
(c)
DS21437B-page 10
2002 Microchip Technology Inc.
TC57
5.3 Package Dimensions
SOT-23A-5
.075 (1.90) REF.
.122 (3.10) .098 (2.50) .020 (0.50) .012 (0.30) PIN 1 .122 (3.10) .106 (2.70) .057 (1.45) .035 (0.90) .006 (0.15) .000 (0.00)
.071 (1.80) .059 (1.50)
.037 (0.95) REF.
10 MAX. .024 (0.60) .004 (0.10)
.010 (0.25) .004 (0.09)
Dimensions: inches (mm)
2002 Microchip Technology Inc.
DS21437B-page 11
(c)
TC57
NOTES:
(c)
DS21437B-page 12
2002 Microchip Technology Inc.
TC57
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART CODE TC57
Output Voltage: Ex: 30 = 3.0V Tolerance: 2 = 2% Temperature/Package: E: -40C to +85C CT: 5-Pin SOT-23A Taping Direction: TR: Standard Taping
XX
02
ECT
XX
Sales and Support
Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
2002 Microchip Technology Inc.
DS21437B-page13
TC57
NOTES:
DS21437B-page14
2002 Microchip Technology Inc.
TC57
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights.
Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, MXLAB, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro (R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified.
2002 Microchip Technology Inc.
DS21437B-page 15
(c)
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com
ASIA/PACIFIC
Australia
Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755
Japan
Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Rocky Mountain
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456
China - Beijing
Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934
Atlanta
500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850
Boston
2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821
China - Chengdu
Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599
Taiwan
Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Chicago
333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924
China - Fuzhou
Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521
EUROPE
Denmark
Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910
Detroit
Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260
China - Shanghai
Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060
Kokomo
2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387
France
Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Los Angeles
18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338
China - Shenzhen
Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086
New York
150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335
Germany
Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955
China - Hong Kong SAR
Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431
Italy
Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883
Toronto
6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509
India
Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062
United Kingdom
Microchip Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820
05/01/02
(c)
DS21437B-page 16
2002 Microchip Technology Inc.
*B73412SD*

▲Up To Search▲

Price & Availability of TC57

	To Download TC57 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .